Analysis of the dispersed composition of dust samples for a cone-shaped dust cleaning device
Abstract. This article deals with the analysis of the dispersed composition of dust samples for a conical dust collector.
Keywords:
Siklon, changli havo, ventilyator, konus setka, dispers, biologik mikroskopAbstract
At present, a large amount of dust is generated during the initial processing of cotton in the cotton ginning industry. As a result, it causes great damage to the environment. In addition, air pollution of industrial buildings with dust has a great impact on the health of workers working there. Currently, single-stage and two-stage dust removal equipment are used in cotton ginning factories to remove dust from the environmental point of view. Dust from cotton gins is sucked up with the help of a fan and sent to cyclones, through which it is cleaned and released into the atmosphere. The cleaning efficiency of cyclones in cotton factories is 60-85% [4]. In cyclones, very small (1.0-10.0 μm) dust particles escape into the atmosphere without being captured. The amount of dust in the air in the production buildings of the cotton ginning plant should not exceed 10 mg/m3. Dusty air released into the atmosphere is 300-350 mg/m3. It can be seen that the concentration of dust in the enterprise is much higher than the norm.
References
Xomidov, Xushnudbek, Elmurod Rabbimov, and Dilnora Baxriddinova. "CALCULATION OF THE DISPLACEMENT OF THE OSCILLATING BEARING ACCORDING TO THE INTENSITY OF THE RADIAL PRESSURE." Инновационные исследования в современном мире: теория и практика 2.17 (2023): 198-199.
Xomidov, Xushnudbek, Dilnora Bakhriddinova, and Sarvinoz Khusanova. "CALCULATION OF HEAT EXCHANGE IN DRYING DEVICES." Молодые ученые 1.5 (2023): 90-91.
Akmalkhonovich, Khamzaev Asrorkhon, Abdullayev Zakirjon Dzhorayevich, and Xomidov Xushnudbek Rafiqjon o’g’li. "CALCULATION OF OPERATING MODES OF CARDS TRANSFERS OF THE EXPERIMENTAL DIGGER FOR HARVESTING TOPINAMBUR." British Journal of Global Ecology and Sustainable Development 16 (2023): 121-126.
Xomidov, Xushnudbek, Dilnora Baxriddinova, and Sarvinoz Xusanova. "QATTIQ YOQILG'INI ISSIQLIK BERISH QOBILYATINI ANIQLASH." Наука и инновация 1.10 (2023): 159-162.
Adhamjon, Akbarov, and Nurmatov Sardor. "METHODOLOGY OF GRAPHIC COMPETENCE DEVELOPMENT OF FUTURE ENGINEERS BASED ON AN INNOVATIVE APPROACH." American Journal of Technology and Applied Sciences 7 (2022): 10-12.
Karimov, Ikromali, et al. "Barbotage absorbation apparatus." Barqarorlik va yetakchi tadqiqotlar onlayn ilmiy jurnali 1.5 (2021): 35-41.
Эгамбердиев, Б. Э., and А. А. Акбаров. "Изучение профиля распределения никеля, имплантированного в кремний, и влияние отжига на структуру." Поверхность. Рентгеновские, синхротронные и нейтронные исследования 6 (2021): 80-84.
Egamberdievich, Egamberdiyev Bahrom, and Nurmatov NeSemiconductors. "Study Of Mechanisms Of Formation Of Silicides Of Cosi2 On Silicon Surface By Ion Implantation." Solid State Technology 63.6 (2020): 18640-18649.
Касимов, Ибрахим Иркинович, et al. "Исследование влияния напряженно-деформированного состояния трехслойных комбинированных пологих оболочек на их физико-механические характеристики." Журнал Технических исследований 3.2 (2020).
Дусматов, Абдурахим Дусматович, Ахаджон Ўрмонжонович Ахмедов, and Зокиржон Жураевич Абдуллаев. "Температурная задача двухслойных цилиндрических оболочек с композиционными защитными слоями." Scientific progress 2.7 (2021): 343-348.
Dusmatov, A. D. "Investigation of strength and stability of three-layer combined plates used in underground structures." Scientific-technical journal 22.2 (2019): 63-67.
Additional Files
Published
How to Cite
License
Copyright (c) 2023 Bilol Yuldashev, Xushnudbek Xomidov, Sardorbek Nurmatov, Farrux O‘lmasov
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
